linuxpakistan.net

Hi to All, Love to them who's help me! :) I've setup TrixBox 2.0, I configured the locals soft phones and each phone can talk to each others. Now its time to setup the Zap Trunk. I am having X101 Clone card as FXO card Plugged the PSTN line into line port. My PSTN info are country code: 92 (Pakistan...

hi to all,
How to adjust the microphone settings in Fedora 6
any hint or tip
=========================
thanks!

Salaam to all, can any body tell me how to check the zap channel status in Asterisk 1.4.5 I've reinstall asterisk but when I issue the following commands it shows that there is no such command available onnected to Asterisk 1.4.5 currently running on 192 (pid = 2454) Verbosity is at least 4 -- Remot...

Dear Farruk bhi,
Salaam,
following are the outputs
[root@192 /]# ps -ef|grep asterisk
root 3367 3324 0 10:39 pts/1 00:00:00 grep asterisk


Is my asterisk fine with this output?
------------------------------------------
Numan Khan

Can you please give me the details of how to execute this command to know the status of alarm.
Best Regards!
---------------------
Numan Khan

Hi to all, I've clone WildCard X101P which is in orginal Ambeint MD3200 (Voice Modem) I've configured it through Zap channel, The FXO channel is configured without any error But the Asterisk is not working at all. I'v checked the card using zttool -v The output is ┌──────────â”...

Can you please tell me in little more details there is also a message that the there is no current alarm Current Alarms: No alarms. │ │ Sync Source: Internally clocked │ │ IRQ Misses: 0 │ │ Bipolar Viol: 0 │ │ Tx/Rx Levels: 0/ 0 │ │ Total/Conf/Act: 1/ 1/ 0 │ │

Well the zttool gives out status ok, if I change the configuration than its gives out unconfigured message. This means the card is doing well except it dont give out Alaram but the status is ok there in Zaptel Tool (C)2002 Linux Support Services, Inc. ┌───────────────...

yes, I did loaded all the zaptel driver modprobe zaptel modprobe wcfxo modprobe wctdm and also checked them lsmod and it shows that the zaptel is loaded snd_seq_device 12621 3 snd_seq_dummy,snd_seq_oss,snd_seq wcfxo 15520 0 zaptel 185148 2 wctdm,wcfxo zaptel drivers are loaded here snd_pcm_oss 46561...

hi to all, I've been playing around asterisk in about one & half week, now I've configured the Zap channel (FXO) All the configuration files are working correctly but still my asterisk server is unable to answer the incoming call. Here are all my configurations files, I hope this would help ;con...

Salaam to all,
can any body answer me this biz question
if
fxs_ks=1
than signalling method must be
fxo_ks
and if
fxo_ks=2 then signalling method must be fxs_ks
simply say yes or not
------------------------------------------
Best Regards
Numan Khan

Salaam to All, With advice & best communciatation of Farruh Bhi, I've configured the FXS channel only and now I am running asterisk with the following command [root@192 sbin]# asterisk -r I've the following dial plan [internal] exten => 611,1,Answer() exten => 611,2,Echo() The Zapata.conf file f...

Dear Farruak Ahmed Salaam, After editing the specified files with your provided code, I am getting this following error for tone, please advise on this [root@192 ~]# /sbin/ztcfg -vv Notice: Configuration file is /etc/zaptel.conf line 9: Cannot get number of tones for channel 1 line 9: Cannot init to...

Hi rahsi thanks for the response, Here are my zapata.conf file context=internal ;user the context in extensions.conf signalling=fxo_ks ;use FXO signalling for FXx challnel channel=>1 ;Telephone attached to port 1 context=incoming ;Incoming calls go to [incoming] in extensions.conf signalling=fxs_ks ...

Dear Brothers, I've Ambient MD3200 card and I am using it both as FXO/FXS channel. The Probelm that I am having is that in /etc/zaptel.conf I assigned as fxoks=1 fxsks=2 loadzone=us defaultzone=us but they they are giving errors as shown below Zaptel Configuration ====================== Channel map:...