hi to all,
I've been playing around asterisk in about one & half week, now I've configured the Zap channel (FXO)
All the configuration files are working correctly but still my asterisk server is unable to answer the incoming call.
Here are all my configurations files, I hope this would help
;configuring FXO channel
/etc/zaptel.conf/
loadzone=us
defaultzone=us
fxsks=1
/etc/asterisk/zapata.conf
[channels]
usecallerid=yes
hidecallerid=no
callwaiting=no
threewaycalling=yes
transfer=yes
echocancel=yes
echotraining=yes
context=incoming ; Incoming calls go to [incoming] in extensions.conf
signalling=fxs_ks ; Use FXS signalling for an FXO channel
channel=>1 ; PSTN attached to port 1
;Here is very basic dialplan
/etc/asterisk/extensions.conf/
[incoming]
exten=>s,1,Answer()
exten=>s,2,Echo()
The output of 'ztcfg -vv' tool is as below
Zaptel Configuration
======================
Channel map:
Channel 01: FXS Kewlstart (Default) (Slaves: 01)
1 channels configured.
The Zttool has verify the hardware status
OK Wildcard X101P Board 1
I've plugged the PSTN line into my FXO port but when I dail my number from external phone, it bypass my Asterisk server, and Asterisk is unable to respond.
Any Help in this regard is highly appreciated.
FXO Channel Problem.
Re: FXO Channel Problem.
Did u load zaptel drivers ??
-
- Lance Naik
- Posts: 19
- Joined: Wed Aug 01, 2007 10:29 am
- Location: San Jose CA United States
- Contact:
yes, I did loaded all the zaptel driver
modprobe zaptel
modprobe wcfxo
modprobe wctdm
and also checked them
lsmod
and it shows that the zaptel is loaded
snd_seq_device 12621 3 snd_seq_dummy,snd_seq_oss,snd_seq
wcfxo 15520 0
zaptel 185148 2 wctdm,wcfxo
zaptel drivers are loaded here
snd_pcm_oss 46561 0
snd_mixer_oss 20545 2 snd_pcm_oss
But still it has problem and server is not responding...
any help or suggestion in this regard is highly appreciated
Numan Khan
modprobe zaptel
modprobe wcfxo
modprobe wctdm
and also checked them
lsmod
and it shows that the zaptel is loaded
snd_seq_device 12621 3 snd_seq_dummy,snd_seq_oss,snd_seq
wcfxo 15520 0
zaptel 185148 2 wctdm,wcfxo
zaptel drivers are loaded here
snd_pcm_oss 46561 0
snd_mixer_oss 20545 2 snd_pcm_oss
But still it has problem and server is not responding...
any help or suggestion in this regard is highly appreciated
Numan Khan
-
- Lance Naik
- Posts: 19
- Joined: Wed Aug 01, 2007 10:29 am
- Location: San Jose CA United States
- Contact:
Well the zttool gives out status ok, if I change the configuration than its gives out unconfigured message. This means the card is doing well except it dont give out Alaram but the status is ok there in
Zaptel Tool (C)2002 Linux Support Services, Inc.
┌────────────────────┤ Zapata Telephony Interfaces ├─────────────────────â”
Zaptel Tool (C)2002 Linux Support Services, Inc.
┌────────────────────┤ Zapata Telephony Interfaces ├─────────────────────â”